Products

Set of meteorological sensors, arranged in a compact assembly to be mounted on a single mast. The integrated sensors are:
- Temperature (inside a solar protector)
- Relative humidity (inside a solar protector)
- Solar Radiation
- Rain gauge (0.2 l)
- Anemometer
- Vane
Each one of the sensors has a specific connector that can be connected to a junction box where the feeds and reading signals are centralized to a single 12 m cable to connect it to the controller that will read the sensors. The unit is equipped with a bird deterrent system to avoid the birds parking.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit

Gauge of rainfall of irrigation water, either by sprinkling or pivot. Manufactured in resistant plastic to the U.V. lightning and other meteorological agents.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L

Sensor plus transmitter for the detection of the presence of rain. Electrically detects the humidity of the surface that, translated to an electrical resistance, geneerates a 4-20 mA output.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensor for reading wind speed, with a transmitter which generates a 4-20 mA output signal for a range or readings from 0 to 120 km/h.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensor for reading the wind direction, with a transmitter which generates a 4-20 mA output signal.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

There are two models, one with voltage output, with the sensor located in sheath of stainless steel and sealed, very easy to install; and another with 4-20 mA output, which incorporates a Pt100 type sensor.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensors with high sensitivity and accuracy, and 4-20 mA output. They can be used for a wide range of premises and different types of environment. There is also a version with an incorporated temperature sensor.
It is advisable to use the ventilated relative humidity sensor for environments with high humidity and high possibility of condensation in the sensor.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

The Vapor Pressure Deficit (VPD) is the pressure measurement, expressed in kPa, of the difference between the vapor saturation pressure (i.e., the pressure at which the air is saturated when reaching the maximum water retention capacity at a given temperature, also called dew point) and the actual vapor pressure.
The VPD value is calculated from the temperature and relative humidity values.
This indicator can be used for disease prevention, determine if there is a risk of condesantion in any part of the system (free water), irrigation needs and/or need to increase humidity in the environment.

It is easy to install in a mast by means of a clamp which is supplied with the sensor. The sensor is protected to bear any adverse climatic conditions: rain, wind, high humidity, etc. 4-20 mA output.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensor for measuring the ambient lighting, reliable and accurate both in exterior and interior conditions. Output current loop 4-20 mA through the same power cable.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensor for reading the flow of photosynthetic photons. 4-20 mA output.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensors for the measurement of the normalized difference vegetation index (NDVI) and for the measurement of the photochemical reflectance index (PRI). SDI-12 output.
Support included.
Compatible with:
- AgroBee-L

High precision displacement sensors through which the dilation and contraction of the trunk or stem can be measured. It is very useful to know if a correct growth of the stem occurs, showing immediately the hydric stress to which it is subjected through the oscillation amplitude of the sensor.
Compatible with:
- Agrónic 2500 (DC3/Verdtech + trans. dendró.)
- Agrónic 4000 (DC3/Verdtech + trans. dendró.)
- Agrónic 5500 (DC3/Verdtech + trans. dendró.)
- Agrónic Bit (DC3/Verdtech + trans. dendró.)
- AgroBee-L
- AgroBee

High precision displacement sensors through which the expansion and contraction fo a plant organism can be measured. It is very useful to know if a correct growth of the organism, immediately showing the water stress to which it is subjected through the amplitude of oscillation of the sensor.
Compatible with:
- Agrónic 2500 (Ecomatik + trans. dendró.)
- Agrónic 4000 (Ecomatik + trans. dendró.)
- Agrónic 5500 (Ecomatik + trans. dendró.)
- Agrónic Bit (Ecomatik + trans. dendró.)
- AgroBee-L
- AgroBee

The transmitter reads dendrometer sensors and transforms the reading into a standard 4-20 mA signal.

Sensors to monitor the relative variations of the flow of sap.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensors to measure the absolute temperature of a leaf.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

Dielectric sensor that reads moisture on the surface of the leaf. It is easy to install and has a high accuracy. The sensor, placed as if it were one more leaf of the plant, imitates the true humidity state of the leaves, measuring the dielectric constant of the top of the sensor.
Compatible with:
- Agrónic 2500 + trans. H2O
- Agrónic 4000 + trans. H2O
- Agrónic 5500 + trans. H2O
- Agrónic Bit + trans. H2O
- AgroBee-L
- AgroBee

Sensors to collect moisture readings in the soil with direct reading in cbar. A controller put into service based on a vacuum pump and accessories is required.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

Sensor used to measure the humidity of the soil where the crop is grown. It is very useful to know the real irrigation scope, letting us to know the real capacity of water retention of our soils.
The Teros 21 sensor also provides floor temperature measurements.
Compatible with:
- Agrónic 2500 (Watermark + trans. Wat)(Teros 21 + trans. SDI-12)
- Agrónic 4000 (Watermark + trans. Wat)(Teros 21 + trans. SDI-12)
- Agrónic 5500 (Watermark + trans. Wat)(Teros 21 + trans. SDI-12)
- Agrónic 7000 (Watermark + trans. Wat)(Teros 21 + trans. SDI-12)
- Agrónic Bit (Watermark + trans. Wat)(Teros 21 + trans. SDI-12)
- AgroBee-L
- AgroBee

Transmitter for reading three "Watermark 200SS" type soil water potential sensors. It includes a temperature sensor for compensating for the value provided by the Watermark sensor.

Transmitter for reading a Teros 21 Aquacheck sensor (3 levels of VWC) or Teros 12.
If working with external modules, you will need a 5W 12V solar panel and support + solar panel regulator with a 7Ah battery.

Sensors for reading the water content in ratio to soil volumetric content m3 water / m3 ground.
Compatible with:
- Agrónic 2500 + trans. H2O
- Agrónic 4000 + trans. H2O
- Agrónic 5500 + trans. H2O
- Agrónic Bit + trans. H2O
- Agrónic 7000 + trans. H2O
- AgroBee-L
- AgroBee

Transmitter for reading ground water content sensors (VWC: Volumetric Water Content) or leaf wetness (Phytos: Leaf Wetness Sensor).

Sensor for reading in ppm the concentration of mineral salts (nitrates and potassium) in soil.
Compatible with:
- Agrobee-L

Sensor for reading the water content in soil in relation to the volumetric content water m3 / soil m3 and electrical conductivity.
Not suitable for Agrónic Monocable.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic Bit
- AgroBee-L
- AgroBee

They are easy to install and long life, they match to most agricultural soils (mineral and hydroponic), and have a high accuracy.
Compatible with:
- Agrónic 2500 + trans. SDI-12/opción SDI-12
- Agrónic 4000 + trans. SDI-12
- Agrónic 5500 + trans. SDI-12/opción SDI-12
- Agrónic 7000 + trans. SDI-12
- Agrónic Bit + trans. SDI-12
- AgroBee-L

Formed by different bi-sensors (soil water content and temperature) installed along its length. Since it is installed perpendicular to the surface of the land, the provided measurements show the characteristics of the soil profile under study.
The maximum distance of a connection fia SDI-12 bus is 50m.
Compatible with:
- Agrónic 2500 (Aquacheck + Op. SDI-12 o trans. SDI-12)(Drill & Drop + Op. SDI-12)
- Agrónic 4000 (Aquacheck + trans. SDI-12)(Drill & Drop Not available)
- Agrónic 5500 (Aquacheck + Op. SDI-12 o trans. SDI-12)(Drill & Drop + Op. SDI-12)
- Agronic 7000 (Aquacheck + trans. SDI-12)(Drill & Drop Not available)
- Agrónic Bit (Aquacheck + trans. SDI-12)(Drill & Drop Not availabre)
- AgroBee-L
- AgroBee (Drill & Drop Not available)

Formed by different tri-sensors (soil water content, temperature and conductivity) installed along its length. Since it is installed perpendicular to the surface of the land, the provided measurements show the characteristics of the soil profile under study.
Compatible with:
- Agrónic 2500 + opción SDI-12
- Agrónic 5500 + opción SDI-12
- AgroBee-L

Sensors that measure the electrical conductivity of irrigation water in millisiemens (mS).
Compatible with:
- Agrónic 2500 (4 Elec. + trans. PH/CE)(2 Elec. + trans. 2 Elec.)
- Agrónic 4000 (4 Elec. + trans. PH/CE)(2 Elec. + trans. 2 Elec.)
- Agrónic 5500 (4 Elec. + trans. PH/CE)(2 Elec. + trans. 2 Elec.)
- Agronic 7000 (4 Elec. + trans. PH/CE)(2 Elec. + trans. 2 Elec.)
- Agrónic Bit (4 Elec. + trans. PH/CE)(2 Elec. + trans. 2 Elec.)

Sensor that measures the pH of irrigation water, on a scale from 0 to 14.
Compatible with:
- Agrónic 2500 + trans. PH
- Agrónic 4000 + trans. PH
- Agrónic 5500 + trans. PH
- Agronic 7000 + trans. PH
- Agrónic Bit + trans. PH

Double transmitter for one pH and one electrical conductivity (EC) sensor reading in the irrigation water. It adapts the signals from the sensors and generates standard 4-20 mA output values to be read by the controller.
It is also available a model for a single pH sensor, and one for a single EC sensor.

Transmitter with the same functions as the previously specified one but with 2-electrode EC sensors (K=1) with temperature compensation by Pt100 of Pt1000 (optional). It admits different brands of EC sensors. but their performances have to be preciously checked.

Sensor for pressure reading, useful to several applications and easy to install. Generates a 4-20 mA output for a range of readings from 0 to 16 bar.
Compatible with:
- Agrónic 2500
- Agrónic 4000
- Agrónic 5500
- Agrónic 7000
- Agrónic Bit
- AgroBee-L
- AgroBee

The transmitter converts the pulses of fertilizer or acid injection into 4-20 mA outputs to manage injectors with a frequency inverter.
For use with devices that do not have analogue outputs at 4-20 mA, for example, the Agrónic 2500 or the Agrónic 5500.

Sensor provides measurements of distances from 500 mm to 9000 mm. The 4-20 mA signal can be set to work at the desired range of distances within the full provided range.
Transmitter that converts the distance measurement provided by an ultrasonic sensor to a standard 4-20 mA output.
Compatible with:
- Agrónic 2500 + trans. 4-20 mA
- Agrónic 4000 + trans. 4-20 mA
- Agrónic 5500 + trans. 4-20 mA
- Agrónic Bit + trans. 4-20 mA
- AgroBee-L 3LV
- AgroBee 3LV

Transmitter that converts frequency meter signals to voltage-free contact pulses.
It allows for working with frequency meters in controllers that only have pulse meter inputs (such as the Agrónic 2500)
The controller leaves the factory adjusted to the frequency/pulse conversion specified by the user, and it can be configured using a Module Reader.